Skip to content
Call 727-386-4629 Mon to Fri, 9 AM to 5 PM Eastern
Identify My PartShippingReturns
0

PGT Door Parts and Hardware for French Doors

PGT built its French doors with locks from two makers, so start at the edge of the panel you open.

  • If that panel has a short plate at the handle and bolts only at the top and bottom, you have the Ashland lock from the PGT 650 or 750. Open PGT Door Hardware.
  • If it has one long strip with hooks standing out of it, you have the AmesburyTruth P3000 from the 5455 or 5555. Its upper and lower cases are on the same page.
  • For handles, open PGT Door Handle Sets. The lock in your door decides the set.

Need help? Send photos

Photograph the door edge and measure the backset. We'll confirm the lock before you order.

Send photosor call 727-386-4629

About PGT

Paul Hostetler and Rod Hershberger founded PGT in 1980 as Vinyl Tech in Venice, Florida, and PGT went on to build impact-resistant windows and doors. PGT has been part of MITER Brands since 2024.

PGT bought its door locks from other makers. It fitted the Ashland concealed lock to its 650 and 750 French doors and the AmesburyTruth P3000 to the 5455 and 5555.

Which PGT Doors These Parts Fit

  • Your PGT 650 or 750 French door takes the Ashland active and passive locks, with a 5/16-18 rod thread.
  • Your PGT 5455 or 5555 French door takes the P3000 upper and lower cases. PGT and its dealers also write the 5455 as FD455, FD-455 and FD5455.

PGT Parts We Carry

  • PGT Door Hardware has the Ashland active lock 56-175 and passive lock 56-176, and the P3000 upper case 56-738 and lower case 56-739.
  • PGT Door Handle Sets carries the Ashland Expressions, True Elegance, Forgings and Evolutions sets for the Ashland lock and the Regency sets for the P3000.

Which PGT Lock Do You Have?

Open the door and look at the edge of the panel you open.

  • A short plate at the handle, with rods hidden inside the door to bolts at the head and sill, is the Ashland lock.
  • One long strip down most of the panel, with hooks standing out of it, is the P3000. It has two cases: the upper one throws the deadbolt for the key, and the lower one holds the latch the handle works.
  • Both measure 2-3/8 inches (60mm) from the door edge to the center of the handle, so the backset will not tell them apart.
  • On the Ashland lock, back a rod out of its coupling. PGT used a 5/16-18 thread, and no other door maker did.

Before Ordering

  • Photograph the door edge with the door open.
  • On a P3000, note whether the key or the handle has failed. The key and deadbolt sit in the upper case, and the handle and latch in the lower one.
  • Keep your rods. The Ashland locks come without them, and nobody sells the 5/16-18 rods.
  • The P3000 cases are special order and non-returnable.

Why Buy From Multipoint Door Hardware?

  • We carry both PGT lock systems and the handle sets for each, so you can repair the door in one order.
  • Send photos through our Identify My Part form and we will confirm the part before you order.
  • Every listing gives the measurements that decide fit, so you can check your door before you buy.

FAQ's About PGT Door Parts

Did PGT make its own door locks?

No. PGT fitted the Ashland concealed lock to its 650 and 750 French doors and the AmesburyTruth P3000 to the 5455 and 5555.

Which lock is in my PGT French door?

Look at the edge of the panel you open. A short plate at the handle with bolts only at the top and bottom is the Ashland lock, and one long strip with hooks is the P3000.

Do I need new shootbolt rods?

No. You reuse the rods in your door. PGT rods have a 5/16-18 thread that no other door maker used, and nobody sells them, so keep yours.

My PGT door will not lock unless I throw the deadbolt first. Is the lock broken?

On a P3000 door that is how the lock works: throw the deadbolt first, then lift the handle. If you lift the handle first, the lock fights you. If the deadbolt will not throw at all, the upper case has failed.

Which handle set fits my PGT door?

The lock decides it. An Ashland lock takes an Ashland set with the key 3-5/8 inches (92mm) above the lever, and a P3000 takes the Regency set.

Do you sell PGT sliding door parts?

No. We carry the locks and handles for PGT hinged French doors.

How do I identify my part?

Photograph the door edge with the door open and both faces of the handles. Send it through our Identify My Part form and we will confirm the correct part before you order.